Ibm 2374 Driver For Mac
Introduction
This page contains the list of device drivers for IBM ThinkPad T42 (2374M91). To download the proper driver, first choose your operating system, then find your device name and click the download button. It is working at a negotiated SATA speed of 3 Gbps Some report a speed of only 1.5 Gbps, but from what I had read before purchasing the Crucial M500, going for a 6 Gbps SSD is worse on a late 2009 Mac as it has to default to the basic SATA 1 speed of 1.5 Gbps, while the slower 3 Gbps SATA II drive works at 3 Gbps. IBM ThinkPad T42 2374 - 14.1' - Pentium M 735 - Win XP Pro - 512 MB RAM - 40 GB HDD Series Specs.
Backlight not working? Use this guide to replace a broken LED driver board.
- Heavy-Duty Suction Cups (Pair)
- Paper Clip
- T10 Torx Screwdriver
- Tweezers
No parts specified.
Stick a heavy-duty suction cup near each of the two top corners of the glass panel.
To attach the suction cups, first position the suction cup with the movable handle parallel to the face of the glass panel (as highlighted in the second picture).
While lightly holding the suction cup against the glass, raise the movable handle until it is parallel with the other handle (as highlighted by the third picture).
If your suction cups refuse to stick, try cleaning both the glass panel and the suction cup with a damp soft, lint-free cloth. (Dampen with distilled water, and if needed, an equal ratio of distilled water and white vinegar for best results.)
Do not use the suction cups to carry the display glass because if one of them fails to stick, you could drop the screen and break it.
The original iMac box makes a good place to store the glass panel. Otherwise, a padded horizontal surface, like a towel on a desk will do nicely.
Gently lift the glass panel perpendicular to the face of the LCD enough to clear the steel mounting pins attached along the underside of the top edge of the glass panel.
Pull the glass panel away from the lower edge of the iMac and carefully set it aside.
Don't use the suction cups to carry the glass panel—if either one loses its grip, the panel could fall and break.
After setting the glass panel down safely, be sure to release the suction cups, as the suction force over time, can crack the glass.
During reinstallation, be sure to meticulously clean the inside of the glass panel and the face of the LCD as any dust or fingerprints trapped inside will be annoyingly visible when the machine is turned on.
Remove the eight T10 Torx screws securing the LCD to the outer case.
Carefully lay the iMac stand-side down on a flat surface.
Due to tight tolerances, you will have to use a thin hooked tool to lift the display out of the outer case. As seen in the third picture, we made one out of a bent paperclip.
Use a thin hooked tool to lift one side of the top edge of the display by its steel outer frame.
After lifting the top edge of the display on one side, hold it out of the outer case while you use a hooked tool to lift the other side. A pencil or pen can be placed under the top edge of the display, parallel to the top edge and extending past the edge of the computer, to keep the first side propped up while lifting the second.
Do not lift the top edge of the display out of the outer case too far, as several short ribbon cables still connect the two components.
Use a pair of tweezers to pull the vertical sync ribbon cable out of its socket on the LED driver board near the top left corner of your iMac.
On some iMacs this may not be a ribbon cable but four separate, very fine and very fragile wires. Be very careful, if the tweezers slip off the plug, you will very likely pull a wire out of the assembly.
Rotate the display out of the outer case enough to disconnect the LED backlight power cable from the LED driver board.
Squeeze the two display data cable connector arms together to unlock it from its socket on the logic board.
Pull the display data cable connector away from its socket on the logic board.
Be very careful when disconnecting this cable as both the cable connector and logic board socket are extremely fragile. When reconnecting the cable later, use as little force as possible.
Lift the display for enough clearance to disconnect the LCD thermal sensor cable connector from its socket on the logic board.
If your fan is spinning full speed after completion, check this connection or the hard drive's thermal sensor cable. The thermal sensor connector socket is very fragile, so be very careful when you connect back the sensor cable.
Carefully pull the display toward the top edge of your iMac and lift it out of the outer case.
Remove the four T10 Torx screws securing the LED driver board to the outer case.
Lift the LED driver board out of its recess in the outer case, minding the DC-In cable still attaching it to the power supply.
Disconnect the DC-In cable by depressing the locking mechanism while pulling the connector away from its socket on the LED driver board.
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
17 other people completed this guide.
Embed this guide
Choose a size and copy the code below to embed this guide as a small widget on your site / forum.
Xbox One Controller Driver For Mac
Preview
Scan performed on 4/26/2017, Computer: HP HP MINI DM1-2010SO - Windows 7 64 bit
Outdated or Corrupted drivers:7/16
Ibm 2374 Driver For Mac
Device/Driver | Status | Status Description | Updated By Scanner |
Motherboards | |||
Intel(R) Xeon(R) E5 v2/Core i7 R2PCIe - 0E34 | Up To Date and Functioning | ||
Mice And Touchpads | |||
Microsoft Microsoft Express Mouse (Mouse and Keyboard Center) | Corrupted By Ibm Thinkpad T40 2374cg5 | ||
Usb Devices | |||
Intel(R) USB 2.0-hub | Corrupted By Ibm Thinkpad T40 2374cg5 | ||
Sound Cards And Media Devices | |||
ASUSTek Philips SAA713X, Hybrid Capture Device | Up To Date and Functioning | ||
Network Cards | |||
Intel(R) PRO/Wireless 2915ABG Network Connection | Up To Date and Functioning | ||
Keyboards | |||
Microsoft HID Keyboard | Up To Date and Functioning | ||
Hard Disk Controller | |||
VIA VIA Bus Master IDE Controller - 5324 | Corrupted By Ibm Thinkpad T40 2374cg5 | ||
Others | |||
Intel Intel(r) AIM External TV Encoder Driver 4 | Corrupted By Ibm Thinkpad T40 2374cg5 | ||
AuthenTec AuthenTec AES3500 TruePrint Sensor | Corrupted By Ibm Thinkpad T40 2374cg5 | ||
NEC Texas Instruments PCIxx12 Cardbus Controller | Corrupted By Ibm Thinkpad T40 2374cg5 | ||
Cameras, Webcams And Scanners | |||
Philips Philips SPC1030NC Webcam | Up To Date and Functioning | ||
Video Cards | |||
ATI ATI Technologies, Inc. 3D RAGE PRO AGP 2X | Up To Date and Functioning | ||
Input Devices | |||
Hewlett-Packard HP Link-5 micro dongle | Up To Date and Functioning | ||
Port Devices | |||
hspa Modem Application4 port (COM7) | Up To Date and Functioning | ||
Monitors | |||
Sony Digital Flat Panel (1024x768) | Corrupted By Ibm Thinkpad T40 2374cg5 | ||
Mobile Phones And Portable Devices | |||
Acer NOKIA | Up To Date and Functioning |